Inverters are an indispensable part of homes and offices. Inverters supply electric power supply to all our important devices. They are extremely helpful during power cuts. This is the reason we buy utility Inverters to install in our homes. We get uninterrupted power supply from inverters. When your Luminous Inverter is Showing Overload and Low Battery, you can get it repaired following the steps mentioned here.
Luminous Inverter is the top Inverter Brand in India. However, all electronic devices can malfunction at any time. They can become faulty after long years of usage. They can also get damaged due to weather conditions. Other external and internal factors can also influence the damage.
Some inverter problems can be resolved easily on your own. Other more serious inverter issues need an expert hand.
Luminous Inverter Showing Low Battery – Luminous Inverter Showing Overload And Low Battery Part 1
Imagee source : Pinterest
The below Luminous Inverter showing overload and low battery are discussed in detail for your reference.
Inverters stop functioning suddenly when you need them the most. This could cause panic and stress. This problem is usually caused due to tripped inverters. Damaged or disconnected batteries can also lead to the fault. The issues can also result from, loose battery terminals or batteries running out of power.
- If the power switches are defective, contact the service providers for help and repair.
- When your inverter the batteries get damaged, replace them. When the inverters get tripped press, the inverter reset button. It is available in your device. Use it to readjust the inverters.
- If the batteries are dead or if they become weak it is recommended to switch off the batteries. You can switch it off just for a short period of time.
- You can switch on or restart the inverter later on.
- If the batteries become old replace them with new ones.
- This will enhance the power transmission.
- If the terminals of the batteries become loose, check for any dust and clean them regularly.
- Tightening the connections may work too.
When Inverter Shows Low Battery
A common difficulty encountered with Luminous inverters is that the batteries stop charging. The batteries may become dead and old over time. You should replace old and damaged batteries with new working batteries.
The battery malfunction could also result from
- Burnt Rectifiers
- Improper Connection and
- Melted Fuses
In these instances, calling for professional help could be your best option. These are serious issues that need technical expertise. The engineers will look for corrosions in terminals and clean them up.
Brief hours of backup can also bring about problems. It deteriorates the working of an inverter. Charge the batteries frequently and properly. The backup time may decrease when the battery looses electrolytes.
- When there are high consumptions of power during power cuts, try and reduce the extra load. This will allow for more back up time.
- Recharge the batteries of the inverters with distilled water.
- Maintain proper water levels for better performance.
How To Reset Luminous Inverter Overload
In order to reset Luminous Inverter Overload, follow these seps below:
- The alarms in inverters may beep continuously sometimes. This is usually due to overloading of Luminous Inverter showing overload. It could also be due to a stuck cooling fan.
- To reset Luminous Inverter Overload, remove all extra loads.
- The inverters might continue to beep even after removing the extra load. In this case, contact the service providers for help and support.
- All inverters are equipped with cooling fans inside the unit. These fans maintain a steady temperature. If the fans stop working, temperature will increase.
- This causes a sudden shut down of the inverters. You will hear alarm notifications soon.
- If this happens, shut down your Luminous Inverter immediately.
- When fans stop rotating and cooling the system, you will hear alarms too.
- An LCD system gone wrong displays wrong voltages. This means the circuits are not working properly.
- Reach out to the Repair technicians to solve this problem.
- When external damage occurs, check the condition of batteries. Also check its connections, terminals, battery load etc.
- Sometimes, inverters produce unpleasant sounds due to winds.
- But when there is excess noise, you should have your fans cleaned.
- If this does not reduce the sound, you may also think of replacing the fans in the Luminous Inverter.
If your inverter shows an overload fault, as a first step, you can check the external connections. This usually solves most overload fault problems. Perform the following steps to confirm the root of the problem.
- Inverter test
- Appliance test
- Cabling test
Steps To Check If Luminous Inverter Is Showing Overload
Imagee source : Pinterest
- Switch off the inverter.
- Charge the battery to the full extent.
- Check that the battery terminals are clean.
- Secure the Cables from the inverter firmly with the battery.
- Disconnect all appliances.
- Switch on the inverter and check if the overload condition is still there.
- If the overload error persists, press the reset button on the inverter.
- If it has one or switch it off and then on again.
Even after this, if the problem remains unsolved, the inverter must have short circuited.
Steps To Confirm If Connected Devices Are Faulty – Luminous Inverter Showing Overload And Low Battery Part 2
- The total power consumption of the connected appliances should not exceed the inverter power capacity. Connecting one device at a time can help you determine the result.
- Check the appliance’s surge power rating. Ensure it does not exceed what the inverter can handle.
- Faulty appliances with a short-circuit can also trigger an inverter overload fault. This happens when you connect them to the inverter.
Steps To Confirm If Cabling Is Damaged
- It is possible for faulty cabling to cause an inverter overload fault. If here is a short-circuit in the cabling, it could cause inverter overload.
- To rule out faulty cabling, disconnect the appliance.
- If there is a fault in the cabling, the inverter overload will continue.
Luminous Inverter Showing Overload
The below are indicators of Luminous Inverter Showing Overload.
- Luminous inverters have an overload protection. The inverter could shut down if the rated power exceeds.
- Depending on the inverter design, the internal breaker can trip.
- With Luminous Inverters, a breaker trip leads to overload. Usually good quality inverters like these react the same way.
- Manually reset this. It might reset itself once the overload clears.
- If the Luminous Inverter showing overload on LED, it could be faulty.
- It may also make a continuous or alarm notification.
Quick Fix For Luminous Inverter Showing Overload – Luminous Inverter Showing Overload And Low Battery Part 2
- Install a fuse of the appropriate rating depending on the inverter.
- If the inverter shows an overload with no device connections, then there is an internal fault in the inverter.
- You can try resetting it. You can follow the steps mentioned in the manual.
- If the fault persists then you need to have the inverter checked out. Call up a qualified technician to come take a look.
Take Away
- Follow the steps mentioned in the product manual to repair the Luminous Inverter Overload and Low Battery.
- Try to check for all reasons causing the problem.
- Replace Battery if your Luminous Inverter is showing low battery.
- Reset your inverter if Luminous Inverter is showing overload.
- If all else fails, contact a technician. They will fix your Luminous Inverter showing Overload and low battery.
